[1] Heidari, M. R.; Adami, A. H. "General Grain Analysis and Rapid Internal Ballistic Simulation for Solid Motor"; Iranian Scientific Association of Energetic Materials, Vol. 5., No. 2, 2011, pp. 59-72 (In Persian).
[2] Chorin, A. J. "Flame Advection and Propagation Algorithms"; J. Comput. Phys. Vol. 35, No. 1, 1980, pp. 1-11.
[3] Osher, S.; Sethian, J. A. "Fronts Propagating with Curvature-Dependent Speed: Algorithms Based on Hamilton-Jacobi Formulations"; J. Comput. phys.,Vol. 79, No. 1, 1988, pp. 12-49.
[4] Atılgan, T. K.; Tuğrul, T. H.; Haluk, A. M. “Three-Dimensional Internal Ballistic Analysis by Fast Marching Method Applied to Propellant Grain Burn-Back”; 41st AIAA/ASME/SAE/ASEE. Joint. Propul. Conf. Tucson, AZ, USA. 2005.
[5] H. Karimi, M. Moradi, H. Abtahi." Three-dimensional grain burn-back geometric modeling with quite complex profiles by SolidWork software";in The 6th Conference of Iranian Areospace Society, Tehran, Iran, 2006. (In Persian).
[6] Willcox, M. A.; Brewster, M. Q.; Tang, K. C.; Stewart, D. S. "Solid Propellant Grain Design and Burnback Simulation Using a Minimum Distance Function"; J. propul. Power. 2007, 23(2), 467-477.
[7] Yildirim, C.; Aksel, M. H. “Numerical Simulation of the Grain Burnback in Solid Propellant Rocket Motor”; AIAA. Pap. 2005, 4160.
[8] Qin, F.; Guoqiang, H.; Peijin, L.; Jiang, L. "Algorithm Study on Burning Surface Calculation of Solid Rocket Motor With Complicated Grain Based On Level Set Methods"; 42th AIAA/Am. Soc. Mech. Eng. Soc. Auto. Eng. Soc. Explos. Eng. Joint Propul. Conf. Exh. 2006.
[9] Favini, B.; Cavallini, E.; Di Giacinto, M.; Serraglia, F. "An Ignition-to-Burn Out Analysis of SRM Internal Ballistic and Performances"; AIAA. Pap. 2008, 5141.
[10] Toker,K. A.; Alsel, H.; Tinaztepe, T. "3-Dimentional Propellant Grain Burn back Calculation on Tetrahedron Mesh by Fast Marching Method"; AIAA, 2004.
[11] Moshir Estekhareh, S. G. Numerical simulation of the grain burn-back in solid propellant rocket motor, MS Thesis, Department of Mechanical and Aerospace Engineering, Maleke-ashtar University of Technology, Tehran, 2012 (In Persian).
[12] Gheisari, M, M., Mirsajedi, S, M.,"Using marching cube algorithm for 3D grain burn-back analysis in Solid Rocket Motors based on level set method";Modares Mechanical Engineering, Vol. 14 No. 15, 2015, pp. 85-95 (In Persian).
[13] Tshokotsha, M.H.,. Internal ballistic modelling of solid rocket motors using level set methods for simulating grain burnback, (Thesis PhD), Stellenbosch: Stellenbosch University, 2016.
[14] Pons Lorente, A. Study of grain burnback and performance of solid rockets motors, (Thesis Master), Jet. Propul. 2013, pp. 8-10.
[15] Cavallini, E,. Modeling and numerical simulation of solid rocket motors internal ballistics, 2010.
[16] Summerfield, M. Solid Propellant Rocket Research, Princeton University: Prinncton, New Jersey. 1960, pp. 207-227.
[17] Zucrow, M.J. and Hoffman, J.D., Gas Dynamics: Volume2-Multidimensional Flow, John Wiley & Sons, Inc., New York. 1977, p. 488.
[18] Hoffman, Z., "Gas Dynamics Volume I J. Padhye, V. Firoiu, and D. Towsley, “A stochastic model of TCP Reno congestion avoidance and control,” Univ. of Massachusetts, Amherst, MA, CMPSCI Tech. Rep,1999, pp. 99-02.
[19] Kays Morrow, W., Convective heat and mass transfer, Tata McGraw-Hill Education, 2012.
[20] Heidari, M, R,. Adami, A, H,. “Specific Grain Analysis and Rapid Internal Ballistic Simulation for Solid Motor”; Journal of Space Science & Technology, 2012, pp. 67-80 (In Persian).
[21] ThiokoVhuntsvill, A. L. "Application of the Saderholm Erosive Burning Model to Nozzleless Solid Propellant Rocket Motors", 1984, 35807
[22] Willcox, M. L.; Brewster, M. Q.; Tang, K. C.; Stewart, D. S. and Kuznetsov, I. R. "Solid Rocket Motor Internal Ballistics Simulation Using Three Dimensional Grain Burn Back"; J. Propul. Power. May-June 2007, pp. 575-584.
[23] Sutton; George, P., Babilarz, O., Rocket Propulsion Elements, John & Sons, 2017, pp. 165-167.
[24] Cavallini, E. Modeling and Numerical Simulation of Solid Rocket Motors Internal Ballistics; (Thesis PhD), 2010, pp. 37-43.
[25] Parsa, R, E,. Mirsajedi, S. M., "Effects of Erosive Burning on Solid Rocket Motor Internal Ballistics"; Journal of Space Science & Technology, 2012, pp. 69-74 (In Persian).
[26] Konert, M. Vandenberghf, J. F. “Comparison of Laser Grain Size Analysis with Pipette and Sieve Analysis: a Solution for the Underestimation of the Clay Fraction,” Sedimentology, Vol. 44, No. 31, 1997, pp. 523-535.
[27] Cavallini, E.; Favini. B.; Giacinto, M. Di. “Internal Ballistics Simulation of a NAWC Tactical SRM.,” J. Appl. Mech, Vol. 78, 2011, pp. 1005-1018.