Space subsystems design: (navigation, control, structure and…)
hamid reza ali mohamadi; Hassan Naseh
Articles in Press, Accepted Manuscript, Available Online from 25 September 2023
Abstract
Achieving to new technologies with high reliability, along with reducing the cost and time of the design cycle, is one of the most important challenges in complex systems. In this paper, reliability based design of a space system is discussed in the conceptual design phase. Normally, there are eight ...
Read More
Achieving to new technologies with high reliability, along with reducing the cost and time of the design cycle, is one of the most important challenges in complex systems. In this paper, reliability based design of a space system is discussed in the conceptual design phase. Normally, there are eight steps in the design for reliability. The first step, planning, and the next seven steps that applied for the liquid propellant engine with electro-pump technology included: determination of failure modes; reliability modeling; reliability allocation; propagation of uncertainty; Implementation of the chosen method in reliability analysis; reliability prediction and reliability evaluation. Therefore, in this research has been performed to achieved method and implementation steps of reliability design in the conceptual design phase of a space system.
H. R. Ali Mohammadi; D. Ramesh; M. R. Heidary; R. Farrokhi; H. Karimi
Volume 6, Issue 3 , October 2013, , Pages 1-13
Abstract
In this paper, a particular propulsion system including, liquid rocket engine, fuel and oxidizer tank and related pressurizing system, have been surveyed. The procedure is based on a nonlinear mathematical model which has been simulated in Matlab Simulation environment. In propulsion systems, identifying ...
Read More
In this paper, a particular propulsion system including, liquid rocket engine, fuel and oxidizer tank and related pressurizing system, have been surveyed. The procedure is based on a nonlinear mathematical model which has been simulated in Matlab Simulation environment. In propulsion systems, identifying system performance is essential, because if we can accept ability describe the dynamic behavior of the system components in nominal and transient regimes, we can reduce the associated costs during design and development. Following, results of Propulsion system hot test are compared with model that shows acceptable accuracy of simulator code. In addition to leading research, how to use this model to identify the causes of failure is shown. Match analysis and compatibility testing, after disassembling objective observations show considerable performance model for similar applications.
H. R. Ali Mohammady; D. Ramesh; M. R. Heidary; R Farrokhi; H. Karimi
Volume 6, Issue 1 , April 2013, , Pages 11-19
Abstract
Providing of sufficient input pressure of pumps is Pressurizing system tank mission. In structure of objective propulsion system, pressurizing system of fuel tank is hot gas kind that is feeding with engine which caused of operation relational. In this paper, interaction of pressurizing system of fuel ...
Read More
Providing of sufficient input pressure of pumps is Pressurizing system tank mission. In structure of objective propulsion system, pressurizing system of fuel tank is hot gas kind that is feeding with engine which caused of operation relational. In this paper, interaction of pressurizing system of fuel tank and liquid rocket engine has been surveyed. Objective system consists of four main subsystems: liquid rocket engine, fuel tank, gas mixer and pipes. The procedure is based on a nonlinear mathematical model that dynamically describes operation of favorite system by regard to interaction of subsystems. Then all of the equations have been simulated in Matlab Simulation environment. Finally, results of propulsion system hot test are compared with model that shows acceptable accuracy of simulator code.
M. Naghikhani; H. R. Ali Mohammadi
Volume 4, Issue 1 , July 2011, , Pages 61-67
Abstract
Selection of the optimal tolerance for the components is one of the most important and complex issues in the design of the parts and products especially in sensitive and accurate industries (like as aerospace). Generally the design engineers tend to consider close tolerances in terms of product performances ...
Read More
Selection of the optimal tolerance for the components is one of the most important and complex issues in the design of the parts and products especially in sensitive and accurate industries (like as aerospace). Generally the design engineers tend to consider close tolerances in terms of product performances and high reliability, on the contrary to manufacturing engineers that used to open tolerances because of easier, cheaper and practicality of manufacturing processes. Study the balance between tolerance and other factors affecting it, such as quality, cost and production, is the most important issue in this case. In this regard, there are numerous articles and methods. In this paper we use the tools of statistics and mathematics as" response surface method", first method of diagnosis of the critical tolerances describes and then tolerance of the optimal allocation - in case the cost of production or quality characteristic is optimized- has been examined.
