[1] Movahednezhad, E., Investigation of Spray using Maximum Entropy Model, PhD Thesis, Maechanical Engineering, Tarbiat Modares University, 2011 (in Persian)
[2] Huimin, Liu,. “Science and Engineering of Droplets: Fundamentals and Applications”, Noyes Publications, 2000.
[3] J. Shinjo, A., "Umemura, Simulation of liquid jet primary breakup: Dynamics of ligament and droplet formation," International journal of multiphase Flow, Vol. 36, No. 7, 2010, pp. 513-532.
[4] Shinjo, J., Umemura, A., "Surface instability and primary atomization characteristics of straight liquid jet sprays," International Journal of Multiphase Flow, Vol. 37, No. 10, 2011, pp. 1294-1304.
[5] Nukiyama, S., Tanasawa, Y., Experiments on the atomization of liquids in an air stream, 1939.
[6] Lorenzetto, G., Lefebvre, A., "Measurements of drop size on a plain-jet airblast atomizer," AIAA Journal, Vol. 15, No. 7, 1977, pp. 1006-1010.
[7] Eroglu, H., Chigier, N., Farago, Z., "Coaxial atomizer liquid intact lengths," Physics of Fluids A: Fluid Dynamics (1989-1993), Vol. 3, No. 2, 1991, pp. 303-308.
[8] Engelbert, C., Hardalupas, Y., Whitelaw, J., "Breakup phenomena in coaxial airblast atomizers," in Proceeding of The Royal Society, pp. 189-229.
[9] Mayer, W., Branam, R., "Atomization characteristics on the surface of a round liquid jet," Experiments in fluids, Vol. 36, No. 4, 2004, pp. 528-539.
[10] Varga, C., Lasheras, J.C., Hopfinger, E., "Initial breakup of a small-diameter liquid jetby a high-speed gas stream," Journal of Fluid Mechanics, Vol. 497, 2003, pp. 405-434.
[11] Villermaux, E., Marmottant, P., Duplat, J., "Ligament-mediated spray formation," Physical review letters, Vol. 92, No. 7, 2004, pp. 074501.
[12] Liu, H.-F., Li, W.-F., Gong, X., -K. Cao, X., Xu, J.-L., Chen, X.-L., Wang, Y.-F., Yu, G.-S., Wang, F.-C., Yu, Z.-H., "Effect of liquid jet diameter on performance of coaxial two-fluid airblast atomizers," Chemical Engineering and Processing: Process Intensification, Vol. 45, No. 4, 2006, pp. 240-245.
[13] Baharanchi, A.A., Darus, A.N., Ansari, M., Baharanchi, E.A., "An optimum method of capturing interface and a threshold Weber number for inclusion of surface tension force in simulation of nozzle internal flow in pressure swirl atomizers," in Proceeding of American Society of Mechanical Engineers, pp. 135-146.
[14] Mosavi, S.H., Development of a Maximum entropy Model to Investigate the Spray failure of a two- pin injector, PhD Thesis, Mechanical Engineering, Tarbiat Modares University, 2015 (in Persian).
[15] K. Sallam, Z. Dali, G. Faeth, Liquid breakup at the surface of turbulent round liquid jets in still gases, International journal of Multiphase Flow, Vol. 28, No. 3, 2002, pp. 427-449.
[16] Lefebvre,
A. H., Atomization and sprays, Washington, DC: Hemisphere Publishing Corporation, 1989.
[17] Baumgarten, C., Mixture Formation in internal Combustion Engines, Berlin: Springer, 2006, pp. 294.
[18] Negeed, E.-S., Hidaka, R.S. M., Y. Takata, K., "Experimental and analytical Investigation of liquid sheet breakup characteristics," International Journal of Heat and Fluid Flow, Vol. 32, No. 1, 2011, pp. 95-106.
[19] Batarseh, Z., F., Gnir B., M., V. Roisman, I. and Tropea, C., “Fluctuations of a spray generated by an air blast atomizer”, Experiments in Fluids, Vol. 46, 2009, pp. 1081-1091
[21] Watanawanyoo, P., Hirahara, H., Mochida, H., Furukawa, T., Nakamura, M. and Chaitep, S., “Experimental investigations on spray characteristics in twin-fluid Atomizer”, Procedia Engineering, Elsevier Publisher, Vol. 24., 2011, pp. 866-872,
[22] Reitz, R.D., "Mechanisms of atomization processes in high-pressur evaporizing sprays," Atomization Spray, Vol.3, No.8, 1987, pp. 309-337.
[23] A. Kushari, Y. Neumeier and O. Is, "Internally Mixed Liquid Injector for Active Control of Atomization Process," J. Propul.Power, Vol.17, No. 4, 2001, pp. 878-882.
[24] Chen, S., Fan,Y. Yan, Z., WangandCLu, W., CFD "simulation of gas–solidtwo-phase flow and mixing in a FCC riser with feed stockinjection," Powder Technol, Vol. 287, 2016, pp. 29-42.
[25] Cheng, C., Li, H.X., Feng, Y.C. and Feng, Y., "Application of discrete element method in numerical simulation of swirl nozzle," J. Eng.Thermo phys, Vol. 36, No. 10, 2015, pp. 2183-2187.
[26] Gnirß, M., Roisman, I.V., Tropea, C.,. “Fluctuations of a spray generated by an airblast atomizer,” Experiments in Fluids, Vol. 46, 2009, pp.1081–1091.